74LS688 DATASHEET PDF

Texas Instruments 74LS Logic Comparators are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Texas Instruments . December INTEGRATED CIRCUITS. 74HC/HCT 8-bit magnitude comparator. For a complete data sheet, please also download. Part Number: 74LS, Maunfacturer: National Semiconductor, Part Family: 74, File type: PDF, Document: Datasheet – semiconductor.

Author: Voodoogal Brakora
Country: Belgium
Language: English (Spanish)
Genre: Spiritual
Published (Last): 10 September 2007
Pages: 347
PDF File Size: 10.44 Mb
ePub File Size: 10.63 Mb
ISBN: 594-1-51115-987-7
Downloads: 55586
Price: Free* [*Free Regsitration Required]
Uploader: Zolojar

I’m currently designing the power-on-jump circuit for my processor board. This is all fine. My calculations say yes, with lots of time to spare, but I’d like others’ opinions.

74LS688 Datasheet

Hi I doubt you’ll be able to run the output of the directly to a clock. It is a glitchy signal. I don’t do well with word descriptions of circuits–can you draw a schematic? I got lost reading that.

I’m not that good with circuit design, but is datasheef possible a monostable multivibrator one-shot would do the job?

Here’s the pieces relevant to Power on Jump: Glitchy output shouldn’t be a problem — it needs to be inverted for the D-type flip flop’s clock anyway, so I’m using a 74LS14 inverter, which has Schmitt inputs and should clean up the signal into a nice, sharp positive-going square wave.

Online Electronic Components Shop

It might work, but I don’t like it much. You’re depending too much on the propagation delay of the 74 and the creating 74ls88 clock pulse of the minimum required width t wclk on your datasheet. Glitchy output shouldn’t be a problem — glitch, I see how you got your nickname. As the address lines transition and settle out, they might very well set up a glitch that dataasheet with the test condition, well before you intended.

  KREMANSKO PROROCANSTVO KNJIGA PDF

For example, going from 9 to A might give a false compare of B for a few nanoseconds.

This might cause a false trigger if your address trap was at B. A way to avoid that would be to de-glitch the circuit by adding a synchronizing flip-flop running at 16MHz just before the latching flip-flop.

This would also add about 62 nS to your fatasheet clock which right now is only 3 gate delays long and would be difficult to see on an old low bandwidth scope.

74LS | Texas Instruments Distributor | 74LS Inventory

Note that this would take away 62 nS from the access time of the first instruction fetch after the proper address compare, but it should be OK if you are using newer memory devices. There may be better ways to do this job so keep tinkering. Hi No it won’t. It may even make it worse.

I’m not talking about little tiny noise spikes. Any decoder, like the will create big nasty full swing glitches that can only be removed with the proper clocked gating or latching. If you expect to use it, you need to turn the enable off during the time when the compare inputs are in transition.

  FOCUSRITE OCTOPRE PLATINUM MANUAL PDF

You could then use it as a clock. You can’t use it while the inputs are changing.

74LS Datasheet PDF –

Just to scratch my own curious itch, what does the connect to? In other words, what function does satasheet serve? I’ve never had to use one. It’s comparing the high four address bits to a 4-position DIP switch.

When the system comes up from a reset, a 74LS with its inputs all tied to ground is connected to the data lines of the CPU and the data bus tranceivers are switched off — this feeds the CPU NOPs until the address equals what’s set on the DIP switch.

This sets the D-type flip flop, which switches off the NOP generator and turns on the bus tranceivers.

It’s an 8-bit comparator, but it’s cheaper than the 74LS85 and has an enable input.