ASTM D4066 PDF

Buy ASTM D CLASSIFICATION SYSTEM FOR NYLON INJECTION AND EXTRUSION MATERIALS (PA) from SAI Global. ASTM D Standard Classification System for Nylon Injection and Extrusion Materials (PA). standard by ASTM International, 07/01/ View all product. 暂无评价|0人阅读|0次下载 | 举报文档. D – 01A Nylon Injection and Extrusion Materials_能源/化工_工程科技_专业资料。ASTM D标准.

Author: Akizuru Yozshushicage
Country: Mayotte
Language: English (Spanish)
Genre: Art
Published (Last): 18 September 2010
Pages: 231
PDF File Size: 5.27 Mb
ePub File Size: 16.69 Mb
ISBN: 567-2-21389-129-5
Downloads: 50719
Price: Free* [*Free Regsitration Required]
Uploader: Mazulrajas

Requirements are based on unannealed test specimens 3. This example can asfm applied to replace all table values, that is, tensile stress, notched Izod impact, and heat de?

Link to Active This link will always route to the current Active version of the standard. These are electrical limits applied to reinforced nylons when control of their electrical properties is required. This standard does not purport to address all of the safety concerns, if any, associated with its use.

This standard has been approved for use by agencies of the Department of Defense. After the humidity conditioning speci? It is possible that materials incorporating other pigments or soluble stabilizers, or both may prove adequate for particular applications. G Izod impact for these materials shall be conducted on specimens with a The electrodes shall be inserted after the specimens have been conditioned.

General Principles ISO Some of these compositions are also suitable for compression molding and application from solution. J Carbon black content and absorbance must be 1. Referenced Documents purchase separately The documents listed below are ast, within the subject standard but are not provided as part of the standard.

  DSC PTK5507 PDF

These will be spelled out in detail and identi? Active view current version of standard. The designation PAG35 indicates the following: D ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

NOTE 3—An example of this classi? A superscript epsilon e indicates an editorial change since the last revision or reapproval. If necessary, additional control of these reinforcements and additives can be accomplished by use of the suffix part c4066 the system see Section 5.

Originally published as D — Packing, Packaging, and Marking Material selection should be made by those having expertise in the plastic?

ASTM D – 13 Standard Classification System for Nylon Injection and Extrusion Materials (PA)

D Practice for Sampling of Plastics. These shall be e4066 upon between the user and the supplier, by using the suffixes as given in Section 5.

It is not intended for the selection of materials. NOTE 8—Ash content of?

Weatherable nylon dd4066 contains 1. The holes shall be drilled as above and then reamed, using a standard-tapered pin reamer, to a sufficient depth to allow the pins to extend approximately Table PA is used to specify the group of nylon and Table A or B is used to specify property requirements.

Industrial & Engineering Plastics

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. It is recommended that the material manufacturer be consulted on all call-outs against this classification system.

  D&D 4E PHB2 PDF

The lot-acceptance inspection shall consist of the tests listed as they apply: Suffix values will override the PA table values. Thus, a letter designation G for glass reinforced and 35 for percent or reinforcement, G35, speci?

To be agreed upon between the user and the supplier.

An example of an unreinforced nylon material is given as follows: The report shall consist of results of the lotacceptance inspection for the shipment and the results of the most recent periodic-check inspection.

Refer to Table X3. It is not intended for the selection of materials. There may be other requirements necessary to identify particular characteristics important to specialized applications. Testing Conditions ISO Military and Federal Specifications and Standards: Symbol Material C carbon- and graphite-? Some of these compositions are also suitable for compression molding and application from solution.

The following pieces are to be used for the listed relevant test methods: The test specimen shall be a disk Q For general information not a requirement. If no properties are speci? Seven laboratories, including 3 U.