Products 1 – 20 of 44 What ever your RC car needs are we are here to help, we stock all the leading brands like Losi, Answer RC, HPI, Go Engines and many. Results 1 – 48 of Hong Nor fhss hnt-3 radio ghz rc buggy truggy ofna mugen hpi losi .. (Hong Nor XT) Truggy X1-CRT Steel Spur Gear 62T OFNA. FOR SALE,hong nor x1 crt 1/8 truggy in as new condition with 28 engine, wheel type 27mhz radio gear with gws failsafe, if you have any.
|Published (Last):||6 August 2011|
|PDF File Size:||14.65 Mb|
|ePub File Size:||20.84 Mb|
|Price:||Free* [*Free Regsitration Required]|
Smaller holes, more pack, larger holes, less pack.
Hong Nor X1 CRT IRC / Pro – brushless conversion – Buggies, Truggies & Stadiums – MSUK RC Forum
Share this post Link to post Share on other sites. Anti Squat for RC Beginners. Pack, is the speed your damper reacts to any quick compression hohg can be considered to be a consequence of the size or number of holes in the piston. Bumpsteer – What it is and how to avoid. Lowering the inside camber link position raises roll center and raising the inside camber link position, lowers the roll center.
For more information, take a look at my article, How to get the best from your Bearings.
Sway Bars for Radio Controlled Models. Dust and grit can get into these bearings and abrade the z1. When it comes to tuning your dampers there are basically two things you need to know about pistons. Looked at the rear chassis brace – opted against raising the centre diff using an st pro plate as I want to keep the COG as low as possible.
Few jobs left to do – grind the centre cut out a little so the 52t spur clears comfortable, mod the Losi tray remove switch holder I think so it clears the rear brace, then either sleeve the rear uj so it fits well or as suggested pad it out with a spacer. Rear UJ can now be sourced to correct length or cut n sleeved as, although it fits now, she’s still too short.
Edited April 10, by capri-boy. If instead, it slaps down onto the table, the pack of your dampers is not enough. Concerningly with the centre shafts off there’s a huge amount of play in the drive gear front and rear – investigation is needed. Posted April 30, I thought nong X2’s had the helical cut diffs?
Hong Nor X1-CRT (Radio Controlled Model)
Electric Motors – Tune for Top Performance. Sign in with Twitter. How to Repair a broken Plastic Part. You need to be a member in order to leave a comment.
I hope this article has been helpful. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good drt “Servo Saver”.
When you receive your used Hong Nor Truggy, make a general visual nnor of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced.
Entire assembly sits much lower, couple with the smaller rotating mass handling should show some improvement. RC Information and Advice: Driving Tips – Drive fast, drive smooth. Camber – The easy way to improve handling.
What tooth spur gear is on the X1 CRT please? If your used Hong Nor Truggy comes with plastic and sintered brass bushings ring type bearingscheck the shafts that run in them for wear. I’m loathe to drill the chasiis when I don’t need to. Generally, the manufacturer will suggest one particular piston in the car manual and may provide you with a mid range oil weight, but depending on the type of terrain you intend to race your model, their suggestion may not be the best for your needs.
With an jor manual, any problems with your model Truggy you may discover can easily be fixed.